ዲዛይን SureMAX ቀንዲ ተግባር፡ ናይ ክሳድ ሽንብራት ኢምፕላንት ብ Additive Implants Inc. ኣብ ናይ ውድድር ምድብ ንድፊ ሕክምናዊ መሳርሒታትን ኣቕሑን ኣዝዩ ዝኸበረ ተሸላማይ ናይ 2020 ናይ ነሓስ ሽልማት A' Design Award እዩ።
ነሓስሕክምናዊ ፍርያት· 2020
SureMAX ቀንዲ ተግባር፡ ናይ ክሳድ ሽንብራት ኢምፕላንት
ዓሚል: Additive Implants Inc
ኣብ ምድብ ሕክምናዊ ፍርያት ተሸላማይ ናይ ነሓስ ሽልማት A' Design Award
ዝተረጋገጸ ተሸላማይ
ንቁጽሪ #88502 ሽልማት ኣረጋግጽእቲ ዲዛይን
ብዛዕባ SureMAX ቀንዲ ተግባር፡ ናይ ክሳድ ሽንብራት ኢምፕላንት
ናይ መጽሓፍ ጽሑፍ፦ SureMAX ካብ ታይታኒየም እተሰርሐ ናይ ክሳድ ሽንብራት ኢምፕላንት ኮይኑ፡ ኣብ ናይ ኣንቴርየር ሰርቫይካል ዲስከክቶሚ ኤንድ ፊውዥን ቀዲሕ ቀዶ ሕክምና ዝጥቀመሉ እዩ። ጽንዓት (stiffness) ናይ SureMAX ምስ ጽንዓት ኣዕጽምቲ ናይ ሕሙም ዝሰማማዕ ኮይኑ ስለ ዝተሰርሐ፡ ሽንብራት ኣይትጉዳእን፣ ኢምፕላንትውን ኣይሰጥምን። ኣዕጽምቲ ኣብ ታይታኒየም ብግቡእ ይዓቢ፣ ግናኸ ናይ ቀደም ታይታኒየም ኬጅታት ኣዝዮም ጽኑዓት ነይሮም። SureMAX ብሰለስተ-ውጥናዊ (3D) ሕትመት ካብ ናይ ታይታኒየም ብናጭ (powder) ስለ ዝስራሕ፡ ብመሽን ክስርሑ ዘይክእሉ ቅርጻታት ንኽህልዉ የኽእል። ላዕለዋይ ገጽ እቲ ኢምፕላንት ብዙሕ ነኸውቲ (porous) ኮይኑ ንዕቤት ኣዕጽምቲ ንኽድግፍ ተሸራሪፉ ዝተሰርሐ እዩ። ጎኖታዊ መስኮታት ድማ ብኤክስ-ረይ ምስሊ ናይ ምሕዋይ መስርሕ ንኽርአ የኽእሉ።
እቲ ኣፍልጦ
ብዛዕባ ናይ ነሓስ ሽልማት A' Design Award
SureMAX ቀንዲ ተግባር፡ ናይ ክሳድ ሽንብራት ኢምፕላንት ናይ ነሓስ ሽልማት A' Design Award ዝዓወተ እዩ፣ ብፈጠራ፣ ርእሰ ሓይልን ስቕታን ዝፍለዩ ብልጫ ዘለዎም ዲዛይናት ዝወሃብ ኣዚዩ ክቡር ኣፍልጦ። ዘዓወቱ ነሓስ ሰፊሕ ተሞክሮ፣ ምሕሳብን ርእሰ ምምዕባልን ዲዛይነራቶም ዘረጋግጹ ኣዚዮም ክኢላታትን ብዘደንቕ መገዲ ፈጠራውያንን ኣርቴፋክትታት እዮም። SureMAX ቀንዲ ተግባር፡ ናይ ክሳድ ሽንብራት ኢምፕላንት ብዙሕ ዝተመነየ፣ ዝደነቐን ዝፈተዎን ብኣገዳሲ መገዲ ሞያውን ሓድሽን ኣቕሓ ክኾን ይጽበ። እዚ ዝዓወተ ዲዛይን ናይ ነሓስ ሽልማት A' Design Award ኣብ ጥበብ፣ ሳይንስ፣ ዲዛይንን ቴክኖሎጂን ዝበለጹ ልምድታት ዘጣምር፣ ንዝርዝር ብዝህቦ ኣቓልቦ ድማ ዝበለጸ እዩ። SureMAX ቀንዲ ተግባር፡ ናይ ክሳድ ሽንብራት ኢምፕላንት ድልየታት ብጽባቐ የማልእ፣ ንድሌታት ይትንክፍ፣ ንስምዒታት የማርኽን ሕቶ ድማ የሰሕብን።
ድሕሪ እቲ ዲዛይን
ናይ ፕረስ ኪት
ክረዲትታት፣ ኣባላት ጋንታን ቴክኒካዊ ዝርዝራትን ብዲዛይነር ዝቐረቡ።
- ፍሉያት ባህርያት
- SureMAX is the first Titanium spinal implant that has a stiffness that matches the individual's bone stiffness as not to damage it. Bone loves to grow into Titanium but Titanium cages have been limited because they are too stiff and damage the bone. SureMAX has solved this problem through using 3D print technology with geometries that are not machinable. It also has a porous roughen surface to encourage bone to grow into it.
- ዓቐንን ማዕሸግን
- There are 72 sizes for SureMAX. The height, the foot print and the angle of the implant are the 3 choices. The angles are 0, 7 and 14 degrees. The choice of the angle is used to correct any stenosis in the spine (this is when the spine has a deformity and the implant is used to fix it). The heights are 5,6,7,8,9,10,11 and 12 mm. The foot prints are 12x14 mm, 14x16 mm and 15x118mm. All units come in a sterile plastic package.
- መለለዪታት
- spinal implant, Inter body fusion device, IBFD, cage, Titanium, Ti Cage, 3D printed, Spine
- ናይ ምፍራይ ቴክኖሎጂ
- 3D print technology has been used with Titanium powder (Ti6Al4) using porous surface technology to achieve designs that will encourage bone to grow into the spinal implant
- ናይ ዲዛይን ብድሆ
- To get result required- a high performance implants which is cost competitive, the team had to design a part that could both hand the stresses and forces required by the US government FDA while solving the patient challenges. The part had to be designed so minimal post processing would be required after 3D printing. Additionally, the rough porous surface which helps the healing process required advance software and new methodologies to manufacture. The diving boards had to share the spinal loads equally in order not to displace the implant in the spine. Side windows had to be designed that permits the loads to be distributed and have large have enough surface to see the bone healing. The hardest part of the design activity was to figure out how 8 independent platforms on both sides of the implant could function as a single unit and share the loads appropriately. The surface had to be porous and roughened Ti that could handle the appropriate loads. The teeth had to be the correct size and angle in order to assure stability, but not too big or small to them a ineffective.
- ምርምር
- Titanium (Ti) has always been the material of choice for implants. But Ti is hard to machine and is very stiff. In the interface between Ti and bone, bone can be damaged and the implant subside ( or settle ) in the body. Plastic and Allograft bone material implants are used to address Ti's limitations. Additional, Ti is not X-ray translucent, so physicians can not see how the bone heals through and around the implant. Plastic implants also have the limitation that they remain inert in the body- they are never adsorbed. Bone however grows very well into Ti. The challenge was to create a Ti spinal cervical implant (cervical is for the neck) that had the same stiffness as bone as not to damage it, would not subside (it would stay on top of the bone and not settle), would remain in the position inserted (with the neck movement would not slip), X-ray could go through it (healing could be observed), would pass the stress test required by the FDA and would be cost effective.
- ምንጪ ሓሳብ
- The inspiration was the lack of a solution that took advantage of new geometries that can be created with Titanium which is the best material for bone to grow into by a spine surgeon who performs over 300 cervical surgeries a year. He wanted an implant made from Titanium that matched bone's hardness, not to damage the vertebra, was visible in X-rays, so healing could be seen through, and would not subside in the spine.
- ናይ ፕሮጀክት ግዜ
- The design started in 2015 and ended in October 2018 and FDA approval was received in February 2019 (3 year design and 4 month approval). The work was done in Phoenix Arizona USA.
- ናይ ስርሒት ፍሰት
- The implant is used in an Anterior Cervical Discectomy Fusion (ACDF) surgery where the front of the neck is opened, the damaged cartilage removed and an implant is inserted in order to fuse the vertebra. The implant comes in a sterile plastic package. The surgeon once the damage is observed and removed assesses the size required. The appropriate implant size, angle and foot print is selected and inserted into the spine. A plate is then used (not part of SureMAX) to attach the upper and lower vertebra. The bone then grows into the implant (called inter body fusion device IBFD) and the patient heals.
- ፓተንታት
- Patented #10,299,938 Additive Implants Inc., May 2019, USA
5 additional patent pending and provisional patents
FDA #K182477 (2019), holder Additive Implants Inc. USA
Trademark #88115736 (2018), Additive Implants Inc. USA - ኣባላት ጋንታ
- Dr. John Ehteshami MD
Robert Brosnehan
Matt Zoghi
JD Howell
Jeff Horn
Babak Ehteshami
ስፖንሰር ዝተገብረ
ልዕሊ Designers.org ዳህሰስ
ካብ ናይ ማስታወቂያ መሻርኽትና ፍርያት፣ ኣገልግሎታትን ዕድላትን ፍለጥ።
ተወሳኺ ንምርካብ
ተዛመድቲ ዲዛይናት
ካብ ተመሳሳሊ ምድብ ብብቕዓት ዝተመረጹ ተወሳኺ ሽልማት ዝተዓወቱ ዲዛይናት ድለዩ።
